Fiberglass Dragster Noses, Windscreens & NACA Ducts
Fiberglass Dragster Noses, Lexan Windscreens & NACA Ducts — Pro-Werks
Pro-Werks composite dragster noses are all about quality. The hand-laid fiberglass process produces a consistent wall thickness throughout — resulting in a lightweight, strong composite finished part that holds up to the demands of competitive drag racing. Each nose may be trimmed to match the height, length, and finished mounting requirements of your specific race car. Whether you’re building from scratch or replacing a damaged nose, The Chassis Shop has you covered with Pro-Werks’ proven fiberglass components.
Unlike chopper gun fiberglass, Pro-Werks noses are hand laid by skilled craftsmen — delivering consistent wall thickness for uniform strength, lighter weight, a superior gel coat surface ready for primer and paint, and trimmable edges to fit your specific chassis dimensions. The typical mounting practice is to use Dzus fasteners to secure the nose to the chassis.
Fiberglass Dragster Noses
- Econo Dragster Nose — 8-1/2" Wide × 8-1/2" Tall at Back × 25" Long, — Pro-Werks Fiberglass Econo Dragster Nose — small frontal area, smooth low-resistance design, trimmable to fit, hand-laid fiberglass, Made in USA
- Long Fuel Dragster Nose — 11-3/4" Wide × 8-1/2" Tall at Back × 28" Long, — Pro-Werks Long Fuel Dragster Nose — shapely design cuts through air with minimal resistance, built-in NACA-type feature on top (cut out for function or leave as-is), trimmable to fit, Made in USA
Compatible dragster applications: Top Dragster, Super Comp Dragster, Nostalgia Dragster, Altered, Jr. Dragster, and custom tube chassis builds.
PRO TIP: Trimming & Fitting Your Nose
Pro-Werks dragster noses may be trimmed with a fiberglass-rated cutting wheel or jigsaw with a fine-tooth blade. Always test-fit before final mounting, and finish cut edges with 80-grit sandpaper. Final mounting and bodywork should be performed by an experienced fabricator familiar with composite materials.
Lexan Dragster Windscreens — Clear & Smoke Tint, 4 Sizes
Keep the wind off your face with a properly installed Pro-Werks dragster windscreen. Formed from 1/8" thick scratch-resistant GE Lexan, available in clear or smoke tint. Dimensions are as formed and may be flexed slightly on installation. Top or bottom edges may be trimmed and finish sanded to fit your unique installation. Prepped with a protective coating that dissolves with water before final install.
- Junior Width — 14" Wide (bottom) / 12" Wide (top) / 6" Tall / 25" Long
- Standard Width — 17" Wide (bottom) / 14" Wide (top) / 7" Tall / 33" Long
- Standard Width Tall — 17" Wide (bottom) / 14" Wide (top) / 9" Tall / 33" Long
- Wide Width — 20" Wide (bottom) / 17" Wide (top) / 10" Tall / 33" Long
Pro-Werks Lexan Dragster Windscreen — 1/8" GE Lexan, clear or smoke tint, trimmable edges, covers full-size and junior dragster needs, Made in USA
Fiberglass NACA Ducts — 3 Sizes, Low Drag Air Intake & Exhaust
Pro-Werks universal NACA inlet ducts are lightweight, hand-laid fiberglass construction providing a positive, low-resistance method of air transfer. The mounting flange measures approximately 1" wide and installs with bonding compound, rivets, or small screws on fiberglass, carbon fiber, aluminum, or steel body panels. Mount forward-facing for fresh air intake or reversed as a backward NACA duct to extract hot air. Mount individually or side-by-side for increased airflow volume. Common locations: hood, roof, or side panel.
- 3 Sizes — 3", 4" & 7" Wide, Hand-Laid Fiberglass, 1" Mounting Flange, — Pro-Werks Fiberglass NACA Duct — low drag, installs on any panel material, Made in USA
Note: Final mounting and bodywork should be performed by an experienced fabricator familiar with composite materials.
Complete Your Build
- NACA Ducts — full NACA duct collection including all 3 sizes for brake cooling, cockpit airflow, and engine ventilation
- Dzus Quarter-Turn Fasteners — secure your nose and body panels with quick-release panel fasteners
- Access Door Kits — aeronautical-style aluminum access doors for quick component access behind body panels
- Wings — Pro-Werks aluminum front and rear wings and canards to complete your aero package
Proudly Made in the USA.
